A basic Ethernet port capture is easy – see this tutorial if you’re new to Wireshark. The beauty of Wireshark is it will capture all network traffic on an Ethernet interface, including traffic not in the same IP subnet as your computer. Wireshark is a free network packet capture and protocol analyzer. Use Wireshark to Discover the Camera’s Actual IP Address The good news is with the solution I describe here I can downgrade the firmware at will and recover the camera. The cryptic note in the FTP directory “ Please upgrade the mid FW first before v.5.3.6.txt” didn’t work as I tried that too: HikVision USA FTP Firmware Listing – DS-2CD6412FWD-C2 I found that downgrading to V5.1.7 140904 works fine, re-installing V5.3.0 build 150513 is good but upgrading to V5.3.6 151031 or v5.3.6 160218 mid FW in any sequence always bricks the camera. Hikvision says that firmware upgrades must be applied sequentially. My camera was shipped with firmware V5.3.0 build 150513. The PoE switch, IP camera and laptop per the above network diagram: Isolated Network to Fix Bricked Hikvision IP Camera Firmware You can also use your favorite TFTP server software.įix Bricked HikVision IP Camera – Firmware Upgrade Downgrade Network Diagram The Hikvision TFTP server software is no longer officially distributed. Wireshark includes the older WinPcap library however it’s not Windows 10 compatible. Win10Pcap – Ethernet packet capture library for Windows 10.Wireshark – network protocol analyzer and packet capture.The laptop has the following tools and files: I setup an isolated network using an unmanaged PoE switch between my laptop and the camera. Bricked Hikvision IP Camera Recovery with Wireshark My PC was running the TFTP server at 192.0.0.128 but the camera couldn’t reach it. This means the camera was trying to contact a TFTP server but couldn’t find it at the expected IP address. Also notice the line: |NUL ethaddr| not found tftpserver Route: ioctl 0x890c failed: No such processīusyBox appears to be stuck in a start-up loop. Starting pid 51, tty Starting udev: '': '/etc/init.d/rcS' ![]() Starting pid 51, tty '': '/etc/init.d/rcS' Image Type: ARM Linux Kernel Image (uncompressed) # Booting kernel from Legacy Image at 80007fc0. Link up on port 0, speed 100, full duplex The PuTTY session was helpful but the camera would not respond to keyboard input, so I couldn’t interrupt the boot process by pressing Ctrl+ u to run TFTP from the command line: U-Boot 2010.06-113941 (11:17:39) ![]() Taking a cue from the UART connection to recover Hik cameras at, I bought a USB to TTL Serial Cable from to make a three wire (Ground, Transmit and Receive) serial connection (115200, 8, N, 1, no flow control) to the camera. EdgeRouter Lite Home Network Wall Rack Hikvision Serial Port Console Recovery Method All units are authentic USA versions and I’ve had no issues upgrading the firmware until now. I’ve installed about 1/2 dozen Hikvision IP cameras and a Hikvision NVR. Nor could the Hikvision SADP Tool could not find the camera. ![]() Moreover, I could *briefly* ping the camera at 192.0.0.64 after it powered-up, then the unit was dead. It was confounding because I set my laptop IP address to 192.0.0.128 expecting the camera to be at 192.0.0.64 after a factory reset. The normal process to recover a bricked camera after a failed firmware upgrade is to downgrade to a known working firmware version using TFTP. This should be the IP address after pressing the camera Reset button to force a factory reset: HikVision DS-2CD6412FWD-10 1.3MP Covert Network Camera The red box label states the camera’s factory default IP address is 192.0.0.64. The camera has a UL Listed sticker on the bottom of the unit: HikVision HD Covert Network Camera DS-2CD6412FWD I’d purchased an authentic “red box” USA version Hikvision HD Covert Network Camera. How to Fix a Bricked Hikvision IP Camera Firmware The trick was using Wireshark to discover the camera’s rogue IP address after performing a factory reset to downgrade the firmware with TFTP. All standard recovery methods failed including a Factory Reset, TFTP server and USB-to-RS232 serial port session. inoperable) after upgrading the firmware. My Hikvision DS-2CD6412FWD-10 1.3MP Covert Network Camera bricked (i.e. How to Fix a Bricked Hikvision IP Camera firmware by using Wireshark to discover the camera’s IP address and update the firmware via TFTP.
0 Comments
Leave a Reply. |